Featured post

Types of mechanical forces

-
A force exerted on a body can cause a change in either the shape or the motion of the body.The unit of force in SI system is the Newton(N) and CGS system is dyne.No solid body is perfectly rigid and when force are applied to it,changes in dimension occur.such changes are not always perceptible to the human eye since they are negligible. For the example,The span of a bridge will sag under the weight of a vehicle and a spanner will bend slightly when tightening a nut. It is also important for civil engineers and designers to appreciate the effects of forces on materials.Together with their mechanical properties of the materials. There three main types of mechanical forces that can act on a body.They are 1)Tensile force 2) compressive force and 3) shear force
1 comment

What is gear and types of gears.

-

Types of Gear


  1. Spur Gear
  2. Helical Gear
  3. Herringbone Gear
  4. Bevel Gear
  5. Worm Gear
  6. Rack and Pinion
  7. Internal and External Gear
  8. Face Gear
  9. Sprcokets
    1) Spur Gear-Parallel and co-planer shafts connected by gears are called spur gears. The arrangement is called spur gearing.

Spur gears have straight teeth and are parallel to the axis of the wheel. Spur gears are the most common type of gears. The advantages of spur gears are their simplicity in design, economy of manufacture and maintenance, and absence of end thrust. They impose only radial loads on the bearings.

Spur gears are known as slow speed gears. If noise is not a serious design problem, spur gears can be used at almost any speed.

2)     Helical Gear-Helical gears have their teeth inclined to the axis of the shafts in the form of a helix, hence the name helical gears.

These gears are usually thought of as high speed gears. Helical gears can take higher loads than similarly sized spur gears. The motion of helical gears is smoother and quieter than the motion of spur gears.

Single helical gears impose both radial loads and thrust loads on their bearings and so require the use of thrust bearings. The angle of the helix on both the gear and the must be same in magnitude but opposite in direction, i.e., a right hand pinion meshes with a left hand gear.
3)   Herringbone Gear - Herringbone gears resemble two helical gears that have been placed side by side. They are often referred to as "double helicals". In the double helical gears arrangement, the thrusts are counter-balanced. In such double helical gears there is no thrust loading on the bearings.
4)  Bevel/Miter Gear-Intersecting but coplanar shafts connected by gears are called bevel gears. This arrangement is known as bevel gearing. Straight bevel gears can be used on shafts at any angle, but right angle is the most common. Bevel Gears have conical blanks. The teeth of straight bevel gears are tapered in both thickness and tooth height. 
Spiral Bevel gears: In these Spiral Bevel gears, the teeth are oblique. Spiral Bevel gears are quieter and can take up more load as compared to straight bevel gears.

Zero Bevel gear: Zero Bevel gears are similar to straight bevel gears, but their teeth are curved lengthwise. These curved teeth of zero bevel gears are arranged in a manner that the effective spiral angle is zero.
5)      Worm Gear- Worm gears are used to transmit power at 90° and where high reductions are required. The axes of worm gears shafts cross in space. The shafts of worm gears lie in parallel planes and may be skewed at any angle between zero and a right angle.In worm gears, one gear has screw threads. Due to this, worm gears are quiet, vibration free and give a smooth output.Worm gears and worm gear shafts are almost invariably at right angles.
6)      Rack and Pinion- A rack is a toothed bar or rod that can be thought of as a sector gear with an infinitely large radius of curvature. Torque can be converted to linear force by meshing a rack with a pinion: the pinion turns; the rack moves in a straight line. Such a mechanism is used in automobiles to convert the rotation of the steering wheel into the left-to-right motion of the tie rod(s). Racks also feature in the theory of gear geometry, where, for instance, the tooth shape of an interchangeable set of gears may be specified for the rack (infinite radius), and the tooth shapes for gears of particular actual radii then derived from that. The rack and pinion gear type is employed in a rack railway.
7)      Internal & External Gear- An external gear is one with the teeth formed on the outer surface of a cylinder or cone. Conversely, an internal gear is one with the teeth formed on the inner surface of a cylinder or cone. For bevel gears, an internal gear is one with the pitch angle exceeding 90 degrees. Internal gears do not cause direction reversal.

8)      Face Gears- Face gears transmit power at (usually) right angles in a circular motion. Face gears are not very common in industrial application.
9)      Sprockets-Sprockets are used to run chains or belts. They are typically used in conveyor systems.

Gears may also be classified according to the position of axis of shaft:
a.Parallel
  1.Spur Gear
  2.Helical Gear
  3.Rack and Pinion
b. Intersecting
  Bevel Gear
c. Non-intersecting and Non-parallel
  worm and worm gears

Comments

  1. Babit24 August 2020 at 21:22

    Your info is really amazing with impressive content. Excellent blog with an informative concept. Really I feel happy to see this useful blog, Thanks for sharing such a nice blog. Rack And Pinion Gear Cutting

    ReplyDelete

Post a Comment

Popular posts from this blog

METHODS OF APPLICATIONS OF CUTTING FLUIDS :

-
Image
The method of application of a cutting fluid is very important and depends on the particular operation. These methods vary from hand applications such as use of brush or oil-can to high pressure applications.For high production. The following methods are used.    1)Flood method,    2) Jet method,and    3) Mist method. 1) Flood method : In this method,a reciprocating pump is used to force the coolant over the work and tool.The outlet of the pump is connected to a nozzle through flexible pipe.The nozzle can be adjusted to direct the stream of the fluid at the cutting zone.This is the most common method of application of cutting fluid. 2) jet method : In jet method,a small jet of fluid at high speed is directed at the point of metal separation from the underneath the tool.In high-speed jet system gear or vane type pump is used to maintain high pressure. 3) Mist method : In mist method,the fluid is passed through a specially designed nozzle to form very fine drop
Read more

ADVANTAGES AND LIMITATIONS OF BROACHING:

-
Broaching is an interesting machining process which is used in mass production. It has certain advantages and limitations as compared to the other machining processes.these are given below. ADVANTAGES : 1) Fast and simple process. 2)High degree of accuracy and finish is possible. 3)Any shape of profile can be easily machined. 4) Machining process is completed with one stroke of broach. 5) Life of broach tool is high. 6)Cutting temperature and tool wear is low. 7) Doesn't require a highly skilled operator. 8)Cutting force acts in the clamping direction I.e.,it doesn't tends to lift the workpiece from fixture. 9)cutting fluids can be applied more easily and effectively. 10)Most economical for mass production of components. LIMITATIONS: 1) Not economical for small quantity productions. 2)Cost of broach is high. 3) Tool grinding (broach sharpening) is difficult and expensive. 4) Not suitable to machine a surface having obstruction. 5) The work m
Read more

Tailstock

-
Image
The tailstock is located on right side of the bed i.e.right hand side of the operator. The main purpose of a tailstock on an engine lathe is to support free end of a work during operation.it is also used to hold tools for making holes (twist drills,reamers) adjusted along the bed of the lathe accommodate different lengths of stock.it is provided with set over screw at its base for taper turning alignment.it has cast iron body with bore to accommodate tailstock spindle,and the top portion contains the spindle,tailstock hand wheel, and a spindle clamp for locking the spindle in position. The end of the spindle has a taper bore for holding dead centre,taper shank drills and other tools.the spindle can centre,taper shank drills and other tools.The spindle can be moved in and out of the tailstock by the rotation of hand wheel in anticlockwise and clock wise direction respectively.A tailstock is shown in fig.
Read more